Many draftsmen prefer to use a mechanical lead pointer instead of the sandpaper pad. The mechanical pointer quickly produces a uniform conical or needlepoint. However, the sandpaper pad must still be used to produce other types of points. The resulting needlepoint should be dulled slightly by drawing it lightly across a piece of scrap paper several times. Avoid sharpening pencils near your drawing. Graphite particles will cause smudges that are difficult to erase. A cloth or tissue be used to wipe away graphite particles that cling to the pencil after it is sharpened. A wedge point (view D) will aid an experienced draftsman in the extensive drawing of straight lines. This point is produced by sharpening a pencil to the conical point just described, then flattening both sides on the sandpaper pad. For an elliptical point, hold the pencil firmly with thumb and fingers and cut the lead on the sand- paper pad by a back-and-forth motion, keeping the pencil at an angle of about 25 degrees to the pad. Continue until a flat ellipse is formed, as shown in figure (view E). A good draftsman never uses a dull pencil. Some draftsmen prefer to use mechanical drafting pencils instead of wooden pencils. The lead of a mechanical pencil is sharpened in the same manner as the lead of a wooden pencil. However, the length of the mechanical pencil is not depleted as the lead is sharpened. This is an advantage over wooden pencils that become difficult to use when they are less than 3 in. in length. When leads for the mechanical pencil are exchanged, ensure that the changeable lead grade designator on the mechanical pencil corresponds to that of the lead used.
Friday, October 16, 2009
SHARPENING A PENCIL
To sharpen a pencil, cut the wood away from the unlettered end (view A) with a draftsman’s pencil sharpener or a penknife. The lettered end should be left intact so that the grade of pencil can always be identified. The cut should be started about 1 1/2 in. from the end, leaving a half inch of lead exposed. To produce a conical or needlepoint (view B), which is best for general use, rotate the pencil between the fingers at the same time as the exposed lead is rubbed back and forth across the full length of the sandpaper pad (view C). Many draftsmen prefer to use a mechanical lead pointer instead of the sandpaper pad. The mechanical pointer quickly produces a uniform conical or needlepoint. However, the sandpaper pad must still be used to produce other types of points. The resulting needlepoint should be dulled slightly by drawing it lightly across a piece of scrap paper several times. Avoid sharpening pencils near your drawing. Graphite particles will cause smudges that are difficult to erase. A cloth or tissue be used to wipe away graphite particles that cling to the pencil after it is sharpened. A wedge point (view D) will aid an experienced draftsman in the extensive drawing of straight lines. This point is produced by sharpening a pencil to the conical point just described, then flattening both sides on the sandpaper pad. For an elliptical point, hold the pencil firmly with thumb and fingers and cut the lead on the sand- paper pad by a back-and-forth motion, keeping the pencil at an angle of about 25 degrees to the pad. Continue until a flat ellipse is formed, as shown in figure (view E). A good draftsman never uses a dull pencil. Some draftsmen prefer to use mechanical drafting pencils instead of wooden pencils. The lead of a mechanical pencil is sharpened in the same manner as the lead of a wooden pencil. However, the length of the mechanical pencil is not depleted as the lead is sharpened. This is an advantage over wooden pencils that become difficult to use when they are less than 3 in. in length. When leads for the mechanical pencil are exchanged, ensure that the changeable lead grade designator on the mechanical pencil corresponds to that of the lead used.
Many draftsmen prefer to use a mechanical lead pointer instead of the sandpaper pad. The mechanical pointer quickly produces a uniform conical or needlepoint. However, the sandpaper pad must still be used to produce other types of points. The resulting needlepoint should be dulled slightly by drawing it lightly across a piece of scrap paper several times. Avoid sharpening pencils near your drawing. Graphite particles will cause smudges that are difficult to erase. A cloth or tissue be used to wipe away graphite particles that cling to the pencil after it is sharpened. A wedge point (view D) will aid an experienced draftsman in the extensive drawing of straight lines. This point is produced by sharpening a pencil to the conical point just described, then flattening both sides on the sandpaper pad. For an elliptical point, hold the pencil firmly with thumb and fingers and cut the lead on the sand- paper pad by a back-and-forth motion, keeping the pencil at an angle of about 25 degrees to the pad. Continue until a flat ellipse is formed, as shown in figure (view E). A good draftsman never uses a dull pencil. Some draftsmen prefer to use mechanical drafting pencils instead of wooden pencils. The lead of a mechanical pencil is sharpened in the same manner as the lead of a wooden pencil. However, the length of the mechanical pencil is not depleted as the lead is sharpened. This is an advantage over wooden pencils that become difficult to use when they are less than 3 in. in length. When leads for the mechanical pencil are exchanged, ensure that the changeable lead grade designator on the mechanical pencil corresponds to that of the lead used.
Subscribe to:
Post Comments (Atom)
Posts
No comments:
Post a Comment